|
Making Pendants on your computer |
Gene S Morgan Tiki Socialite
Joined: Jul 18, 2011 Posts: 342 From: Midwest the navel of the USA
| Posted: 2012-09-06 7:22 pm  Permalink
A couple of problems were evident with the smaller size. I think there was less detail on these. It may be because the tutorial sculpt actually had a bit more detail and had more undercuts than the previous ones. I did that on purpose because this is all pretty experimental for me. It may be that this sculpt was just harder for Shapeways to reproduce. Also in the castings, I got more bubble holes on these smaller ones. I believe that is because there were smaller and thinner edges in the detail. Bubbles seem to form in the same places all the time. Any suggestions from folks with more casting experience would be greatly appreciated. All those faults sure made this one look old and worn.
 
 
|
Gene S Morgan Tiki Socialite
Joined: Jul 18, 2011 Posts: 342 From: Midwest the navel of the USA
| Posted: 2012-09-06 7:26 pm  Permalink
A little thicker paint coat on this one kinda covers up some of the defects. But those pesky bubbles are still there. You may notice that this one looks a little different because I cut the top hanger off and drilled a hole in it to see how that would work with a jump ring. I had become concerned that at this smaller size the top hanger might break off, so I tried this other approach.
 
 
|
Gene S Morgan Tiki Socialite
Joined: Jul 18, 2011 Posts: 342 From: Midwest the navel of the USA
| Posted: 2012-09-06 7:29 pm  Permalink
Whystler had suggested to me that I try to have my pendants produced in a smoother material. I tried one in what was called a polished version of the material I was using. This is the sculpt I tried that with.
 
 
|
Gene S Morgan Tiki Socialite
Joined: Jul 18, 2011 Posts: 342 From: Midwest the navel of the USA
| Posted: 2012-09-06 7:32 pm  Permalink
This is a design I produced awhile back as a t-shirt design. It was easy to convert it for a pendant design.
 
 
|
Gene S Morgan Tiki Socialite
Joined: Jul 18, 2011 Posts: 342 From: Midwest the navel of the USA
| Posted: 2012-09-06 7:36 pm  Permalink
These smoother finished tikis take the paint really well. And, they seem to have fewer bubbles. But, I think, again, the small size and polishing reduced the detail. The teeth which are nice in the original sculpt are kind of messed up on the pendant. I was disappointed with that …....
I'm still trying to get this stuff right …. That is all I have for now …...
We have some of these pendants available (and there are more to come) on our website: etsy.com/shop/morgancreativedesign
My t-shirt shop is at: cafepress.com/cidgraphics
 
 
|
Unkl Ian Tiki Centralite
Joined: May 16, 2009 Posts: 28 From: Backwoods of Canada
| Posted: 2012-11-07 7:50 pm  Permalink
If you pour the resin sooner, it gives more time
for the bubbles to float away from the surface.
_________________ www.ModernTiki.com
 
 
|
Unkl Ian Tiki Centralite
Joined: May 16, 2009 Posts: 28 From: Backwoods of Canada
| Posted: 2012-11-08 11:34 am  Permalink
You can also use a soft (disposable) brush, to coat
the mold cavity with resin first.
This breaks up the bubbles on the surface.
 
 
|
Gene S Morgan Tiki Socialite
Joined: Jul 18, 2011 Posts: 342 From: Midwest the navel of the USA
| Posted: 2012-12-26 1:26 pm  Permalink
Thanks very much Unkl Ian for your suggestions. They sure were helpful. I will give them a try. .... Gene
 
 
|